AS-TOP

AS-TOP sont des séparateurs de liquides à faible densité (séparateurs d'huile) conçus pour la capture et la séparation de particules libres à faible densité, en particulier les substances à base d'huile, de l'eau polluée. Les séparateurs de liquides à faible densité sont utilisés pour traiter les eaux usées provenant des installations industrielles, installations de mécanisation, zone de dépôt, aires de stationnement. En quelques mots, tous lieux où l'écoulement des fluides de faible densité se produit ou lorsqu'une grande quantité de liquides à faible densité pourrait s'infiltrer dans les eaux souterraines…

AS-TOP Separators of low-density liquids (oil separators) are designed for capturing and separating free low-density liquids, especially oil substances, from polluted water. Separators of low-density liquids are used to treat wastewater from industrial plants, mechanization facilities, and lay-by and parking areas – in short, in all places where the dripping of low-density liquids occurs or a higher quantity of low-density liquids could leak into groundwater.

AS-TOP Separators of Low-density Liquids feature:

Coalescence filter of special PUR foam, easily removable - easy maintenance
Nominal size in accordance with the EC standard - from 2l/s to ......(based on the customer’s request)
Double-jacketed structure - low purchase and construction costs

The AS-TOP Oil Separators are equipped with:

• Sludge containers, depending on the place of use

type P – Sludge container size 300 x NS for large quantities of drained water (repair areas, washing of constructions, machines)
type VF – Sludge container size 200 x NS for medium quantities of drained water (parking areas of vans and lorries, storage areas)
type RC – Sludge container size 100 x NS for small quantities of drained water (car parking areas)

Double-jacketed structure of the tank of the AS-TOP…EO/PB-SV Oil Separator

The advanced design of the tank combines the advantages of plastic structures with concrete ones.

Advantages:

Easy construction
- Double plastic jacket forming the outer as well as inner formwork
- Built-in reinforcement
- Guaranteed stability of the product after concreting against soil pressure, heavy vehicle traffic, groundwater buoyancy, etc.

Combination of sacrificial formwork and insulation
(after concreting, the plastic jacket serves to insulate the concrete structure against aggressive water)

Easy handling in construction conditions - low product weight, as compared to concrete pre-cast products

All of the tanks of the low-density liquid separators of the AS-TOP ... /PB type are delivered for static loading as standard:
- Soil pressure with the footing bottom depth of 5 m
- Groundwater table up to the drainage level
- Incidental loading of the surface by heavy vehicular traffic
- We will produce an individual static design for other installation needs

Separators of low-density liquids, with the lowest purchasing and operating costs, complying with the requirements of European standards

For investors this means

- Guarantee that the equipment is most likely to comply in the future as well, i.e., in the period after the expiration of the water right approval, which is issued for a limited period of time in accordance with the new Water Management Act.
- Overall cost savings thanks to the new equipment design that has made it possible to reduce total volumes while maintaining the prescribed volumes in accordance with European standards, and that enables a better hydraulic utilization of space. Thus, the purchase price of the equipment has been reduced and the maintenance costs have decreased due to a considerable reduction of the volume of disposed waste.
- • Extension of the service life of the equipment the inner structures are exclusively made of stainless steel, ensuring high resistance and easy operation even after several years of use.

In the design of the types referred to as PB, a new concept of “double-jacketed” tanks was applied, where the inner space between two plastic jackets is filled with concrete at the place of installation. In this way, a structure with high resistance to the external environment is obtained, both with regard to environmental aggressiveness (chemically resistant plastic on the interior as well as exterior) and static strength (strength corresponding to concrete tanks).

For construction companies this means

Handling savings as compared to heavy concrete pre-cast parts
Time savings – the elimination of the formwork and reinforcement installation process (the tanks are supplied with reinforcement) as compared to concreting on conventional monoliths on the spot.
Savings in the execution of special work - elimination of costly insulation
• Not problems with water leaks

For designers this means

Certainty that your project will correspond to the current state of the art
Advantage that during the designing you can proceed in accordance with the European standard, as the nominal sizes of the equipment already comply with it
Time savings compared to designing pre-cast parts

For the environment this means

Equipment complying with the generally accepted European standard will be used, which ensures its safety, with high contractual and guaranteed probability.

In the design of the types referred to as PB, a new concept of “double-jacketed” tanks was applied, where the inner space between two plastic jackets is filled with concrete in the place of installation. In this way, a structure with high resistance to the external environment is obtained, both with regard to environmental aggressiveness (chemically resistant plastic on the interior as well as exterior) and static strength (strength corresponding to concrete tanks).